![]() ![]() ![]() This is because we pair the devices uniquely to the specific wireless receiver for security and encryption purposes. Only one wireless receiver can ever be used with 2:1 or 3:1 pairings. No, you cannot pair all of your devices to more than one SLIPSTREAM wireless receiver. When you are not using a SLIPSTREAM wireless receiver, you should keep the receiver in a safe place in case you want to revert to 1:1 or if you lose your active SLIPSTREAM wireless receiver.Ĭan I pair all of my devices to more than one SLIPSTREAM wireless receiver? What do I do with extra SLIPSTREAM wireless receivers I'm currently not using? Yes, all of your SLIPSTREAM Multipoint devices will reconnect once you select your wireless receiver in ICUE and select Multipoint in the Device Settings. Will my SLIPSTREAM Multipoint devices reconnect after I disable PlayStation mode? However, you can still connect and use those devices via USB cable. When PlayStation mode is enabled, your mice and/or keyboards will disconnect from your headset's SLIPSTREAM wireless receiver. PlayStation mode allows you to connect your SLIPSTREAM-compatible devices such as headsets to your PlayStation console and use them. Note: if you wish to undo multipoint across all of your devices, you will need to enable 1:1 pairing for each device individually.Ĭurrently, PlayStation consoles such as the PlayStation 4 and PlayStation 5 do not support Multipoint device connections. Enabling PlayStation mode will put the wireless receiver in a 1:1 pairing switching from 3:1 firmware to 1:1 firmware will not change the performance of your device. Yes, you can enable PlayStation mode by selecting your headset's SLIPSTREAM wireless receiver in iCUE and going into the Device Settings. Gigabyte RGB Fusion, MSI Dragon Center, ASUS Armoury Crate, etc.) prior to starting the setup wizard.Ĭan I undo SLIPSTREAM Multipoint support? We also recommend closing any third-party software (e.g. This will ensure a clean installation of firmware without hubs interfering with the process. Instead, use either the front USB ports of your PC case or connect all of your devices to the rear USB ports on your motherboard. We recommend that you always keep your devices updated to the latest firmware for the most optimal experience.ĭo I need to prepare anything prior to flashing the devices?įor optimal performance, do NOT use any hubs to flash your device during this process. If all of your devices are on the latest firmware, the pairing process should only take about a minute. Our setup wizard that is built into the iCUE user interface will help guide you through the process of updating to the latest firmware that supports SLIPSTREAM Multipoint and connecting your devices to a single wireless receiver. To enable SLIPSTREAM pairing, you will need to connect each of your devices with a USB cable and then connect the SLIPSTREAM USB wireless receiver that you want to use in the pairing process. When using 3:1 pairing, polling rates will be slightly higher than 1ms, but our internal testing showed no noticeable effect on mice and keyboards, even with a headset SLIPSTREAM wireless receiver driving all three devices simultaneously. When using 2:1 pairing, polling rates supported will be no less than 1ms when using the multi-device pairing. In addition, if your combination includes a headset, you MUST use the headset's SLIPSTREAM wireless receiver to connect your devices.Īre there any drawbacks to using SLIPSTREAM Multipoint? You must use one of the following pairing combinations: When connecting devices using SLIPSTREAM Multipoint, you cannot pair two of the same types of devices together. What Corsair devices are compatible with SLIPSTREAM Multipoint? Keyboards 3:1 pairing: Keyboard + Mouse + Headset.2:1 pairing: Keyboard + Mouse, Keyboard + Headset, Headset + Mouse.There are two combination types for pairings: SLIPSTREAM Multipoint allows you to connect your compatible wireless Corsair devices together through one SLIPSTREAM wireless receiver. How do I recover my devices if the pairing setup wizard gets stuck at 75%?.How do I begin using SLIPSTREAM Multipoint?.Can I pair all of my devices to more than one SLIPSTREAM wireless receiver?.What do I do with extra SLIPSTREAM wireless receivers I'm currently not using?.Will my SLIPSTREAM Multipoint devices reconnect after I disable PlayStation mode?.Can I undo SLIPSTREAM Multipoint support?.Do I need to prepare anything prior to flashing the devices?.Are there any drawbacks to using SLIPSTREAM Multipoint?.What Corsair devices are compatible with SLIPSTREAM Multipoint?. ![]() You can also read our blog post on SLIPSTREAM Multipoint. We have put together this FAQ to help answer any questions about Multipoint that you may have. If your version of iCUE is 4.10.273 or newer, SLIPSTREAM Multipoint connectivity will be enabled in iCUE. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |